When users are seriously limited by real dot alignment accuracy, nothing is workable for users until getting correct use of a high brightness 635nm red laser diode module. It is a high purity red laser light emitting dot alignment tool, which is just making sure of direct dot targeting from its internal 635nm red laser diode. Under condition that it is getting quite easy selection of output power and proper adjustment of laser beam focus, a concentrated red laser dot is just making sure of the clearest dot instruction for all kinds of industrial machinery processing works effectively. If you are only using sticker, laser pointer or your own finger to make dot alignment, it is only workable for very close distance within your hand reaching. However, in current industrial precise device manufacturing works, there are a lot of work places where the real dot alignment work is processed at quite long distance, thus those of manual dot targeting tool is gradually substituted by 635nm red laser diode module. Even though this red laser alignment tool gets the same color red laser light as a 650nm red laser device, however, under condition that both lasers are getting the same output power, this 635nm red laser module is just getting at least 5 times brighter laser light. As a result, under condition that users are in need of the highest level of accuracy dot alignment, this 635nm wavelength made laser dot alignment tool is just the better choice for users. Owing to its quite special laser beam transverse mode of TEM00, no matter what kind of targeting surface, this 635nm red laser diode module is getting the most compact size red reference dot in use. In addition, according to its good equipment of high quality glass coated lens, red laser beam keeps extremely high laser beam transmittance, which has just made the acquired red alignment laser dot clearly visible and bright, and also keeping the most compact size. This red laser module is just able to get only 0,3mm diameter red reference dot at about 10cm work distance from laser beam aperture. No matter what kind of industrial precise device manufacturing work, 635nm red laser diode module is always getting the best use without mistake and high work efficiency. It is a low labor force and money input dot alignment solution, thus getting more and more applicable use for all kinds of industrial precise device manufacturing works. Users just use this dot laser alignment as an accessory part, according to high attention to basic laser safety measures and remember to wear a pair of laser safety goggles, a correct power made red laser module is just able to bring users the most wonderful dot aligning all the time. In current industrial precise device manufacturing works, there are more and more users are beginning to make line alignment with the assistance of advanced laser tech made line measuring tool. For instance, with the assistance of a high brightness green line laser alignment, on basis of its high brightness green laser beam emission from 532nm green DPSS laser tech, it is just obtaining the most easily absorbed green laser light, thus generating the most visible green line in distance. The real laser line alignment work always has no serious limitation of work distance, height and other working environment, but just brining users the clearest green line targeting on all working surfaces.
According to the use of qualified glass coated lens with different optic lens degree, green line laser alignment is just obtaining different laser beam fan angle, getting different size green line length in distance. It is a quite easy job for users to get clear enough line targeting at different working distance only if this green laser line generator is properly selected its output power. Under occasion of inner room and close distance, a 5mW green laser module enough. However, once the real line targeting is processed under high lighting or quite long distance, users should just select this laser line generator with quite higher output power up 50mW. Within its quite wide output power range, green line laser alignment is always designed with different dimension in type of 16mm and 26mm diameter laser tube. In addition, according to its designed external electric power source of DC input power supply, there is quite larger space reserving as its cooling system. The use of metal heat sink cooling system is getting much better performance than simply used air or water cooling, which is just making great work for users to get even more stable and reliable green laser line targeting in distance. When green line laser alignment is being used as an accessory part of industrial device, it is always used with the assistance of laser alignment mounting bracket. With three dimensions free adjustment of laser line targeting direction, it is always taking less than one second time to get clear enough line targeting after proper adjustment of green alignment laser line thickness and line targeting direction. This good direction made laser line generator should also be used with high attention to laser safety measures, according to proper wearing of a pair of laser safety glasses, this laser module device just brings users high security line targeting effectively. If you are worrying a lot about dot alignment accuracy, it is not clever idea for users to still use simple dot targeting tool such as a sticker, laser pointer or your own finger. On contrary, when users are changing mind to seek help from advanced laser diode tech, it is just a great job for users to make good use of economy red dot laser alignment. According to very easy connect with an external electric power source of DC input power supply, supported by different operating voltage of 3V or 4.2V electric power source, this laser diode module is always effective enough to make sure of high speed and high accuracy red laser dot targeting on all desired working surfaces.
This economy red dot laser alignment is always used as an accessory part of other machine or device. It is looking quite similar with a red laser pointer, however, owing to its continuous electric power source from DC input power supply, it is just able to make constant red laser dot targeting. Without spending extra time on changing battery and quite larger space reserving as its cooling system, this dot laser alignment is just effective enough to get superior nice thermal emitting, thus easily getting highly stable and reliable red laser dot targeting in use. When red dot laser alignment is being used as a professional dot measuring tool, no matter what kind of output power it is selected, it is just used as an accessory part of other machine or device. It is able to work with clearly visible and bright red laser dot for laser marking machine, laser engraving machine, military targeting device, and drilling system etc. No matter what kind of working surface, noncontact red dot is making immediate dot positioning. This 650nm red laser module is specially designed with adjustable focus, getting small size red laser dot diameter of only 0.3mm at 10cm distance, and only 1mm to 2mm diameter at about 3 meters work distance from laser beam aperture. This red dot laser alignment is not as bright as 532nm green DPSS laser system, however, in order to get clear enough dot targeting, users still choose higher output power than 532nm green laser device. At the same time, owing to its invisible red laser beam under sunlight, the real laser dot alignment work should just avoid such working occasion. According to exact work distance, users can select this laser diode module with correct output power and make proper adjustment of laser beam focus. Once users are wearing proper laser safety goggles, this laser dot measuring tool just assures secured dot targeting effectively. In a lot of industrial precise device manufacturing works, users are always required to make high speed and no mistake dot alignment on various raw material surfaces. Not the same as formal dot targeting with a sticker, laser pointer or your own finger, in order to get clear enough dot alignment, more and more factory users and engineers are beginning to choose high power 100mW red laser diode module as the first dot alignment choice. Only if this high power red laser alignment is getting the connection with quite higher operating voltage of 4.2V DC input power supply, it is just able to make a high speed and high accuracy red laser dot targeting on various working surfaces.
The laser beam from 100mW red laser diode module is not the same as any other manual dot alignment tool, since it is clearly visible and bright at several miles far away. However, once this high power red laser alignment is used for industrial dot alignment work, once the real dot targeting distance is much longer, red laser dot diameter might become larger, which is not any longer workable for extremely long distance targeting work. In order to get precise enough dot targeting, this high power red laser dot alignment tool is just accepting the maximum work distance of 25 meters. On basis of the good use of metal heat sink cooling system and copper raw material made 650nm red laser diode into high duration aircraft used aluminum alloy housing material, this high power 100mW red laser diode module is just effective enough to obtain superior thermal conductivity, easily obtaining highly stable red laser dot targeting as expected. Not the same as a simple portable red laser device only used for burning experiment, this 100mW red laser module is just an industrial stabilized dot alignment tool, which is able to make super clear dot alignment for laser marking, laser engraving, military targeting and others etc. The operation of high power 100mW red laser diode module is just allowing quite easy installation on any other industrial machine or device. It is not used separately, but just working together with those of devices. According to the assistance of a laser alignment mounting bracket, noncontact red alignment laser dot is able to take less than one second time to reach any targeting surface, making sure of the clearest red laser dot targeting effectively. On consideration of high security dot alignment, users should remember to wear a pair of laser safety goggles until achieving the most secured dot measuring all the time. What is your choice to get an easy and quick line targeting on different targeting surfaces? It is just a hard job to get clear enough line alignment before users are getting correct choice of line measuring tool. As a result, in current industrial precise machinery processing works, there are more users are beginning to seek help from a pro red line laser alignment. Anytime it is being available with different output power and wide range optic lens degree, this laser line generator is easily obtaining a highly straight and fine red reference line in distance.
This pro red line laser alignment is getting the most important use of glass coated lens. This high quality optic lens is just making sure of high linear quality red laser line targeting on different working surface. It is getting better performance than formally used plastic coated lens since it might become dim or blur in long term user. However, once this red laser line generator is employing glass coated lens, whatever kind of working surface, red line is just keeping high linear quality and high laser beam transmittance, thus there is no worrying about laser light decay in long term line alignment work. Under condition that pro red line laser alignment is being used in industrial precise line aligning work, it is mostly used as an accessory part, but not being used separately used as a red laser pointer for burning experiment or others. It is just an accessory part of laser cutting machine, textile garment processing device or others. When red laser line is working together with a laser cutting machine, according to parallel red line with laser cutting knife, it will instruct factory workers to make clear line aligning and line cutting on various raw materials, making sure of no mistake and high speed line alignment as well. In addition, the real laser line alignment work is also leaving no track, but just keeping steady and high work efficiency all the time. According to easy selection of optic lens degree from 10 degree to 110 degree, pro red line laser alignment is able to generate different size red laser line within 0.5 meter to 6 meters. The high fineness red laser line targeting also takes less than one second time to reach any work surface, no barrier or work distance, height and other corner etc. When red alignment laser line is properly adjusted through simple screw of laser beam aperture part, this red laser module is just able to make a no mistake and high speed line alignment on different work surface. Users should also be cautious enough with quite powerful red laser light and wearing proper laser safety goggles so as to get safe line targeting effectively. Whenever you are not much sure whether you are able to get clear enough line alignment or not, it is just not a good idea for users to still make use of very simple line drawing tool such as a square meter or blocking board. On contrary, in order to avoid mistake caused by manual operation and get high efficiency line alignment without mistake, it is just a quite nice chance for users to make good use of high power blue line laser alignment. On basis of the good use of qualified 445nm blue laser diode and metal heat sink cooling system, this laser line generator is always effective enough to get continuous and high speed blue laser line targeting on desired working surfaces.
The use of blue line laser alignment has just saved a lot of time and reduces manual labor focus input a lot. Anytime, without spending a lot of time on prior line positioning work, there is just no need to spend extra time with the assistance of laser line generator. This 445nm blue laser module is always getting quite high output power up 50mW, thus it is just equipped with even higher operating voltage of 4.2V DC input power supply. Blue laser line is generating from the tube immediately after it is getting continuous electric power source. At the same time, under condition that blue line laser alignment is getting quite larger size laser tube with diameter of 26mm, there is just quite larger space reserving as its cooling system. With the perfect configuration with APC driving circuit board, when this blue laser module gets constant electric current and output power supply, it is just able to keep constant blue laser line targeting in long term line aligning work. In formal line aligning work, in order to keep its reliable performance, this laser line generator is just allowing daily maximum operating time of more than 8 hours to 10 hours. Only if laser tube gets several time for cooling down, it is just able to get the most reliable line alignment work. In order to get high security line targeting all the time, the use of blue line laser alignment should be equipped with a pair of laser safety goggles since any high power blue laser module up 50mW might produce thermal energy harmful to human eyes. In addition, it is not allowed to make direct exposure to any powerful blue laser light during the whole process of laser line targeting work. After quite simple installation and adjustment of alignment laser line thickness and laser line targeting direction, this blue laser module is just assuring no mistake line targeting effectively. Every time users are not much sure whether the real dot alignment is correct or not, it is just no kidding work until users are getting proper use of dot alignment tool such as a 100mW red laser diode module. On basis of its continuous red laser dot targeting, once it is working together with those of industrial device, such as a laser marking machine, laser engraving machine, drilling system etc, it is always able to make quite easy and convenient red laser dot instruction on various working surfaces.
The real experience with 100mW red laser diode module is not the same as a burning experiment used red laser pointer. For instance, a battery power made 100mW red laser pointer might be workable for temporary burning experiment, such as burning cigar, pop balloon, but only able to keep constant dot targeting with maximum time of 30 seconds and then burning out for cooling down. However, once 100mW red laser module is designed with external DC power supply and good metal heat sink cooling system, it is just getting quite nice thermal emitting performance, thus always getting clear and continuous red alignment laser dot targeting within 8 hours to 10 hours a day. For the most important of all, owing to the quite efficient design of APC driving circuit, even though red laser diode module gets super rapid temperature increasing in process of continuous laser dot alignment work, it is still getting constant electric current and output power supply, thus always keeping the most reliable red alignment laser dot targeting effectively. At the same time, this 100mW red laser module is an industrial specialized dot alignment tool, only if users are obeying basic laser safety and laser measuring rules, it can easily obtain stable and safe enough dot targeting as expected. The time this high power 100mW red laser diode module is being used as an accessory part of any other industrial device, it is just able to make quite easy installation with the assistance of laser alignment mounting bracket, thus the real laser dot alignment has no obvious limitation of work distance, height and other working environments at all. In order to prevent powerful thermal energy and intense red laser light, once users are remembering to wear a pair of laser safety goggles, this high power red laser alignment just gets no danger targeting easily. If you are not confident enough whether you are able to get clear enough line alignment at quite longer distance, while it is not good job for users to still make use of simple manual line drawing tool. On contrary, according to the use of high brightness 515nm green laser line generator, on basis of its highly bright and visible green laser line emission from 515nm green laser diode, within its quite wide output power range from 5mW to 50mW, the real laser line alignment work is just able to be processed at different work distance, but not just simply limited for hand reaching work place. After correct selection of out power and easy installation, this 515nm green laser module is just able to make sure of high accuracy and high speed line alignment on all working surfaces effectively.
It is a quite real experience for users to get super clear line alignment with the assistance of this 515nm green laser line generator. Supported by external electric power source of DC input power supply, this green laser module is able to work with super quick green laser line targeting. Owing to its super wide range input electric operating voltage from 100V to 250V, this green laser module is able to be used in majority countries and regions on the earth. When green laser line generator gets wide output power range, in order to make sure of its quite efficient thermal emitting in continuous line alignment work, this green laser module is just designed with different tube diameter of 16mm and 26mm. There is just enough space reserving as its metal heat sink cooling system, together with its stable line alignment performance under harsh working occasion of strong interference or strong static, no matter what kind of industrial line alignment work, only if this 515nm green laser module is getting correct choice of output power, it is easily brining users clear enough line targeting in distance. The selection of high duration aircraft used aluminum alloy housing is an important part to make sure of stable line alignment in wide range working environment. Besides quite stable line alignment performance, this green laser line generator is bearing strong mechanical shocking or calibration, which is just getting superior stable line alignment performance in multiple working environments. When users are making quite easy installation of green laser alignment, within the maximum work distance of 25 meters, it is just assuring no mistake line aligning for both industrial and high tech line positioning works conveniently. Anytime you are trying to get a clear and quick enough line alignment at different working surface, it is just a very hard challenge before the real selection of proper line measuring tool. In current industrial machinery processing work, a lot of users have just given up the use of simple manual line drawing tool, but just beginning to work with the assistance of a high brightness glass lens red laser line generator. Only after quite easy connect with DC input power supply, supported by 3V or 4.2V operating voltage, this 650nm red laser module can easily obtain highly bright and visible red laser line, making sure of super clear and quick line alignment on all targeting surfaces effectively.
The design of 650nm red laser line generator is not the same as any other manual line drawing tool or a laser pointer, which is a totally industrial stabilized line alignment tool workable for long term continuous line alignment work. When it is getting continuous electric power source from DC input power supply, it is just supporting red laser module within quite wide range output power from 5mW to 100mW, thus making sure of quite clear and easily visible red laser line targeting under all lighting working occasions Once red laser beam is pointed under sunlight, none of laser beam can be observed by human eyes, thus the operation of red laser line generator should always avoid sunlight. In addition, according to exact work distance, height and other working environments, this red laser module should be properly selected of its output power. It is not correct for users to always select high power. At the same time, after proper measurement of required red laser line length, line thickness and work distance from laser beam aperture part, users can easily get proper recommendation of required output power and optic lens degree from laser tech engineers. According to the assistance of laser alignment mounting bracket, even though some of working place is very difficult to reach, red laser line generator is still getting quite easy laser line targeting. Red alignment laser line targeting is just allowing three dimensions free adjustment of line targeting direction, thus noncontact red line just takes less than one second time to reach any work surface, making sure of the clearest red line instruction effectively. At the same time, once red laser module is being used with quite high power up 50mW, in order to prevent powerful thermal energy and avoid hurt caused by eye exposure, users should wear a pair of laser safety goggles until getting the most secured line alignment perfectly. |
AuthorA generous sharing of technology and information of industrial alignment laser, laser pointer and fiber testing tools. Archives
July 2018
Categories
All
|